VMware

Powercli One-Liner to List ESXi Host UUID

June 6, 2016

I had to list the host UUID of all the ESXi hosts in an environment recently. This is just a quick post, to show how to grab this information using PowerCLI. After pointing the PowerCLI session at the relevent vCenter (or ESXi host), run the following: Get-VMHost | Select Name,@{n=”HostUUID”;e={$_.ExtensionData.hardware.systeminfo.uuid}} This results in listing each […]

0 comments Read the full article →

VCP6-CMA – Create and Manage Tenants

June 3, 2016

When you deploy vRA, a default tenant is created, with the build in administrator account, (administrator@vsphere.local) being granted access to log in. From there, the default tenants settings can be changed, and new tenants can be created. Note that the default tenant is the only one that supports native AD authentication. Additional tenants that use […]

0 comments Read the full article →

VCP6-CMA – Deploying vRealize Components – vRO – Configuration

May 30, 2016

This post follows on from my previous one, where I covered deploying the vRO appliance, along with some initial configuration tasks. Picking up where I left off, the next task is to head back to the vRO appliance’s homepage (https://vRO-FQDN:8281), which is where the vRO client can be downloaded from: The client runs on Windows, […]

0 comments Read the full article →

VCP6-CMA – Deploying vRealize Components – vRO – Appliance Deployment and Configuration

May 24, 2016

Following on from my recent posts on deploying vRA and IaaS, this post will cover deploying and configuring the vRealize Orchestrator appliance. Due to resources in my lab environment I will be deploying a single vRO instance, using the embedded database. In production, it’s recommended to use a more highly available configuration for vRO. Deploying […]

0 comments Read the full article →

VCP6-CMA – Deploying vRealize Components – IaaS

May 17, 2016

This post follows on from deploying the vRA appliance. Here, I’ll be looking at deploying the IaaS components. I’ll be using the minimal deployment model, which will install all the necessary IAAS components on the same Windows server. In production you’d likely want to use a distributed deployment. The IaaS deployment is made up of […]

0 comments Read the full article →

VCP6-CMA – Deploying vRealize Components – vRA Appliance

May 12, 2016

This post is intended to cover the VCP6-CMA objective around installing and upgrading the vRealize components. When deploying vRA its recommended to deploy onto a vSphere dedicated management cluster, with the aim being to have separation between the management/infrastructure components and the virtual machines that provide services to users and run business applications. A typical […]

0 comments Read the full article →

Deploying a Secondary Cisco Nexus 1000v VSM

March 22, 2016

I recently wrote about deploying the Cisco n1000v switch in a vSphere 5.5 environment. That post covered the initial deployment and configuration tasks. This post picks up where I left off, and will go over how to add a secondary VSM to add redundancy to the n1000v deployment. Deploying a secondary VSM is very similar […]

0 comments Read the full article →

Deploying Nexus 1000v Switch on vSphere 5.5

February 22, 2016

In this post I will cover how to deploy the Cisco n1000v switch on vSphere 5.5 – including the initial deployment of the switch appliance, some initial configuration, followed by deployment of a second VSM to make the deployment highly available. If you’re still reading then you likely already know what the n1000v is and […]

0 comments Read the full article →

Deploying a Highly Available Platform Services Controller Topology – Part 3 – Configuring Citrix Netscaler

January 15, 2016

This post follows on from my recent posts on configuring highly available Platform Services Controllers. By the end of my previous post on this, I had deployed two platform services controllers, configured as a subordinate CA, and configured with the VMware HA scripts. The next step is to configure the external load balancer to provide […]

0 comments Read the full article →

A Look at Site Recovery Manager 6.0 – Part Five – Running a Test Recovery

July 30, 2015

If you’ve checked out the other pages in this series you’ll know that I’ve been setting up an SRM 6 lab, and following the last post on creating recovery plans, it’s now ready to test a failover.  Looking at the summary tab in ‘Site Recovery’, it shows that all the configuration tasks have been completed […]

0 comments Read the full article →